DetailsThe TS 75 EQ Plunge Cut Track Saw ia capable of cutting material that is 2-3/4" thick, this saw will leave an edge that is both burn and splinter-free, creating edges that are clean enough to glue without any further prep work. Suitable for cutting solid doors, truing rough lumber, cutting out window frames, and a host of other applications. Save time and create matched panels by cutting stacked sheet goods with one cut. When used with Festool guide rails, you have ultimate control over the TS saw for perfectly straight cuts. Add the replaceable splinterguard, and a splinter-free cut is achievable on both sides of the blade. Spring-loaded riving knife (splitter) keeps the cut kerf open so that the material does not pinch the blade. This reduces the chance of kickback. The slip clutch helps to minimize the risk of a kickback and minimizes wear on the blade, gear case, and motor. Blade changes are easier and safer using the FastFix system which locks switch and arbor simultaneously for easy arbor bolt removal. The TS 75 makes the actual cut right on the edge of the scribe line, even on bevel cuts. Variable speed allows you to match the speed of the saw to the material. The electronics also maintain a consistent speed under load, improving cut performance and protecting the saw’s motor from thermal and current overload. Simple depth adjustment allows you to expose only the part of the blade necessary for the cut. The plunge action allows cut placement anywhere on the cut line for straight cuts or cut-outs into material.
The MFT/3 has 85% more working area than the older MFT 800, and is 15% lighter than the MFT 1080. Even though the MFT/3 has many improvements, Festool did not abandon features that you have come to trust and enjoy— like perforated tops, side channels for attaching clamps, and folding legs to allow two working heights, and easy transport. Can easily be carried to a jobsite, due to its compact size and light weight. Accurate and repeatable cuts with the guide rail and plunge saw or routers. Clamp faster with uniform holes and Festool clamps. The height has been adjusted from previous models and offers a more comfortable work surface height. Use with legs folded out, at full height, or folded in and set on the floor. The integrated guide rail system allows you to cut with confidence. Adjustable to a maximum cutting depth of three inches, accurately cut materials over 27 inches in width - a feat which is impossible with the largest of miter saws. Combined with Festool TS Series saws, Trion jigsaws and OF Series routers, the guide rail is used to make precise, splinter-free cuts that are safer than with a conventional table or radial arm saw. The angle unit supplied with the MFT3 Multi-Function Table attaches using the V-Groove side rail enabling easy removal and quick, accurate reattachment. Using the angle unit's detents, make precise angle cuts at common angles. Changing the cut angle is much easier when compared to a miter saw where the entire saw head must be repositioned. Allows the guide rail and saw to remain stationary while repositioning the workpiece and fence. The angle stop, which is attached to the Multi-Function Table using the V-Groove side rail, prevents movement of the angle unit by stabilizing the end of the fence. The tensioning knobs are placed further from the side of the MFT to provide ample room for rotating the knob without damaging your hands. Rubber foot caps protect the floor which is especially important while working on the job site. The integrated T-Groove side rail to quickly and easily connect two or more Multi-Function Tables (MFTs) to one another with the optional connectors (484 455) sold separately. The perforated work surface and integrated side rails of the Multi-Function Table provide a wide variety of clamping configurations. Built to be sturdy, the MFT can support loads up to 260 lbs. The threaded inserts not only prevent damage to the MDF top from over torquing but also establish a reference point when attaching the top.
- TS 75 EQ Plunge Cut Track Saw
- Imperial scale for setting the depth of cut
- Arbor size: 1.101" (30 mm)
- Bevel cuts: 0º - 45º
- Cutting depth on guide rail: 2-3/4" (70 mm) straight down and 2 1/8" (55 mm) at 45°
- Cutting depth without guide rail: 2-15/16" (75 mm) straight down
- Power consumption: 1600 watts / 13 amps 120 v AC
- Saw blade diameter: 8-1/4" (210 mm)
- Saw blade speed: 1,350 - 3,550 rpm
- Weight: 13.6 lbs. (6.2 kg)
- MFT/3 Multifunction Table
- Max. working width (with FS Guide Rail): 27-9/16" (700 mm)
- Max. workpiece thickness (with FS Guide Rail): 3-1/16" (78 mm)
- Table dimensions: 45-9/16" x 30-7/16" (1157 x 773 mm)
- Weight: 62 lbs (28 kg)
- Work space: 43-3/8" x 28-1/4" (1102 x 718 mm)
- Working height [folded down]: 35-7/16" [7-3/32"] (900 mm [180 mm])
TS 75 EQ Plunge Cut Track Saw, MFT/3 Multifunction Table, Guide rail, Limit stop, Plug-it power cord, Saw Blade, Slipclutch, Splinterguard, Systainer, Adjustable stop, Angle unit (protractor head), Fence rail, Fence rail clamp, Guide rail FS 1080, Guide rail supports (2x), Hose Deflector.
- Additional Information
Includes 2 Tools Power Source Corded