DetailsThe HL 850 lets you cut flush to an adjacent surface because it can plane across the entire width of the rabbet. Because the planer head is mounted to one side, it sits flush with the opposite side of the planer housing. The retractable side guard makes planing safer, and it swings up and to the side as the rabbet depth increases. Planing up to the edge in deep rabbets is no longer a problem. Single knife cutter-head with spiral design with replaceable cutting knife for a smooth, quiet and “chatter-free” cut. Multiple head options to create rustic architectural effects in beams and flooring. Unlimited rabbeting depth with flush cutter side design and retractable spring-loaded guard. Rotary handle depth adjustment allows precise depth setting to 1/256" (1/10 mm) up to 9/64" (3.5 mm). MMC Electronics - equipped with soft-start for no-jolt starts, and constant speed under load, for consistent cutting speed and smooth results. With the addition of a bench unit stand and angle stop (not included), the HL 850 becomes a stationary jointer for working edges. Efficient chip extraction with left or right side mounting. Quick Blade Changes just loosen 3 screws, replace the blade, tighten back up and that is it! The blade is self-aligning. Thumb-Lock Depth Control makes depth setting a streamlined one-hand operation so you can easily adjust your depth settings to match the resistance of the material.
The CT AutoClean has an integrated filter cleaning mechanism that periodically knocks the dust free of the filter. This guarantees maximum air flow and prevents the filter from becoming caked with dust. The filter cleaning frequency is controlled by a dial and can be completely disabled. The CT AutoClean can be used as a regular dust extractor when run without the AutoClean enabled. Includes an ultra-light weight, flexible anti-static (AS) hose for use with the PLANEX Drywall Sander and other tools that accept a 36mm (1-1/2") hose. Automatic Tool Start & adjustable suction with tool triggered or manual on-off switch and infinitely variable suction force, can be used wet or dry. Sys-dock and hose garage feature allows for the storage and transport of Festool Systainers (not included) on the top of the flat, low-profile unit. An ergonomic handle, large wheels, low center of gravity, and ergonomically balanced design allows you to move the CT effortlessly around the jobsite. With an industrial design for heavy use the CT is equipped with over 24 feet of 12 gauge cord. A cord wrap is supplied to attach to the rear of the unit. With 137 CFM and only 62 dB (on the low setting), the CT 36 can quickly and quietly remove large amounts of debris, with minimal noise. A high performance 1-micron filter comes standard and offers the ultimate in clean air and filtration. The CT 36 AutoClean is specifically designed to complement the PLANEX Drywall Sander but can also be used as a general dust extractor for all tools. An optional smaller 27mm diameter hose may be required for some tools, such as sanders.
- HL 850 Planer
- Cutting depth: 0 - 9/64" (0 - 3.5 mm)
- Imperial scale for setting the depth of cut
- Drive shaft speed: 11,000 rpm
- Head width: 3 15/64" (82 mm)
- Noise level at idle: 79 dB (A)
- Power consumption: 850 watts / 7 amp 120 volts AC
- Rabbeting depth: Unlimited
- Weight: 8.6 lbs. (3.9 kg)
- CT 36 AutoClean Dust Extractor
- Container Capacity: 9.5 gal
- Dimensions (in.): 24.8" x 14.4" x 23.4"
- Filter Bag Capacity: 8.9 gal
- Max. Suction Force: 137 CFM
- Noise Level: 62 - 72 db(A)
- Power Consumption: 350-1200 watts, 2.9-10.0 amps
- Static Water Lift: 96"
- Weight: 29.8 lbs.
HL 850 Planer, CT 36 AutoClean Dust Extractor, Parallel guide, Rabbet depth guide, Solid carbide standard blade, Standard planer head, Systainer, 36mm Antistatic Hose, Cord Wrap, Hose Garage, Self-Cleaning Filter Bag.
- Additional Information
Includes 2 Tools Power Source Corded